Tools

You need to know this about laser tools

What models exist and what to expect.

You need to know this about laser tools

You need to know this about laser tools

Forget Laser, Critical Core Benefits

You need to know this about laser tools

The best grinding machine

You need to know this about laser tools

This measures your house

The tools we will show here make everything all right, and it’s easier to do jobs alone, as before you could be two to handle.

Three variants

There are roughly three variants of lasers: Point lasers, line lasers and rotating lasers, says Gorm Nilsen, engineer specialist at Bosch..

– With a few exceptions, rotating laser is intended for pro users. If you are a hobbyist, I first recommend checking out a point or crossover, “he says. no.

point Laser

A spot laser produces three or five points.

These are tools that create strong light and quality variants can be used outdoors.

The most usable models shoot more rays at all levels. In addition, they usually shoot two rays in the horizontal plane 90 degrees apart and in the water.

What can be used for

You need to know this about laser tools

Line Lines: With lines in cross, the tiles align both ways. Photo: Illustration: Øivind Lie

You need to know this about laser tools

Point laser: Good alternative to solder string

Gary Katz in Fine Homebuilding writes that a proper spot laser can replace a vater.

It’s faster to use than a serpentine cord, and it’s impossible to influence wind or high altitude, she writes.

To get all the corners ninety degrees on a construction, put the spot laser in one of the corners.

Then make the two points that are completely angular.

Line Laser

– The simplest lineages produce a line, while the more advanced produces up to four lines and preferably 90 degrees to each other, writes Katz.

– There are also varieties that create lines in the horizontal plane that go around the entire room (360 degrees). It’s only the most powerful variations you can use outdoors, preferably combined with a recipient, she writes.

What can be used for

The horizontal and vertical lines (cross-glasses) can be used when laying tiles, installing kitchen décor, doing flooring and other work where it is going to be right both ways.

There are also variants that additionally produce one point, and then you’re close to an all in one solution.

Leveling

The laser beam is emitted from a laser diode and ends as a streak or point on the wall.

The simplest variants are equipped with a dragonfly so you have to make sure the laser is in the water.

The more advanced ones are self-leveling.

Laser diode hangs on a pendulum so it will level itself until it hits the internal wall of the tool.

On more advanced variations, you get a signal when the angle becomes too large.

Accessories

In particular, the line loader has a lot to say what it’s on when it’s used.

The easier you can move it up or down or wrap it, the more useful it becomes.

There are different racks from simple tripods to advanced telescope systems, straps to hang in the ceiling and suction cups.

Two important tips

1. Take a check in store

First of all, you need to check the quality of the laser diode itself when shopping for laser tools.

It should be Class 2.

A bad line laser gives a wool or blurred line when it hits the wall at greater distances. Then it can be difficult to determine where it starts or ends.

A simple check you can do in the store is to put the laser five feet away from the wall and check the line you get on a white wall or a white sheet. Then it must be sharp and nice, not like a wool thread.

You should also be able to walk two meters from the line on the wall and still look good, even in good retail lighting.

2. The wall in plot

When you work on a wall, if you use a line laser, you should check if the wall is in bulk.

Is not it, you will get a vertical line distortion if you only turn the laser so that the line moves laterally, for example three meters. Then you will see that the line falls from you or reaches you at the top.

The regions will be right if you move the laser with you so that it stands 90 degrees to the wall at any time.

Read Consumer Testing Laser Tools

Sources:

Gorm Nilsen, Tool Specialist Bosch

FineHomebuilding.com

17 Tips for Hanging Images

How to use a gun gun

.

Leave a Reply

Your email address will not be published. Required fields are marked *

Adblock Detected

Please consider supporting us by disabling your ad blocker